1 t flat endless sling, made of polyester webbing
violet EN 1492-1 safety factor 7:1 width 30 mm loop without eyes
The 1 t flat endless sling, violet, also called an endless sling, is a loop of polyester webbing, 30 mm wide, without eyes, for light loads: bundled pipes and sections, machined parts, small equipment or packages moved with a hoist or an overhead crane. It is used in a straight lift, choke hitch or basket hitch, and in a basket hitch with parallel legs it lifts up to 2,000 kg. On finished surfaces, polyester webbing is gentler than chain or steel wire rope. The effective working lengths are 1, 2 and 3 m (circumference 2, 4 and 6 m); other lengths are made on request.
Straight
1,000 kg
Choke hitch
800 kg
Basket hitch, parallel legs
2,000 kg
Width
30 mm
Effective working length
1, 2 or 3 m
Circumference
2, 4 or 6 m
Working load limit by lifting mode
Straight
loop between hook and load · factor 1.0
1,000 kg
Choke hitch
choked · factor 0.8
800 kg
Basket hitch
parallel legs, β ≤ 7° · factor 2.0
2,000 kg
Basket hitch
β 7°–45° · factor 1.4
1,400 kg
Basket hitch
β 45°–60° · factor 1.0
1,000 kg
Two slings, straight
β ≤ 45° · factor 1.4
1,400 kg
Two slings, straight
β 45°–60° · factor 1.0
1,000 kg
Two slings, choke hitch
β ≤ 45° · factor 1.12
1,120 kg
Two slings, choke hitch
β 45°–60° · factor 0.8
800 kg
β is the angle between the sling leg and the vertical. Lifting at an angle β above 60° is prohibited. In a choke hitch, the value applies only when the loop tightens freely around the load, at its natural angle (about 120°), without being forced. The values in the table are the maximum mass of the load for the lifting mode indicated, for a load that is centred and distributed evenly across the legs. The sling label always takes precedence.
Technical specifications
| Working load limit (straight) | 1,000 kg |
|---|---|
| Colour (EN 1492-1 code) | violet |
| Webbing width | 30 mm |
| Type | flat endless sling (a loop of webbing) without eyes |
| Material | polyester (PES) |
| Standard | EN 1492-1 |
| Safety factor | 7:1 |
| Label | blue (polyester), stitched to the sling |
| Working temperature | −40 °C … +100 °C |
| Lengths (effective working length / circumference) | 1 m / 2 m; 2 m / 4 m; 3 m / 6 m (other lengths on request) |
Length: effective working length and circumference
For the flat endless sling, the length is stated as a pair: effective working length / circumference. The effective working length is the distance measured between the two ends of the loop, with the sling laid flat on a level surface, that is, between the bearing points at the hook and at the load. The circumference is the total length of the webbing, that is, twice the effective working length: for “2 m / 4 m”, the effective working length is 2 m and the total webbing length is 4 m.
In a straight lift, the effective working length must cover the distance between the hook and the attachment point on the load. In a choke hitch or basket hitch, the sling goes around the load and needs more length. Longer legs help keep the angle β to the vertical within the limits given in the table. If the length you need is not available, we make the sling to order, to the length you require.
Flat endless sling, round sling or webbing sling with eyes?
The flat endless sling is a loop of woven polyester webbing, without eyes, made to EN 1492-1, the same standard as for flat webbing slings with eyes. The wide webbing bears on a large area of the load, and the loop can be positioned differently for each lift, so that the contact points with the hook and with the load are not always the same. The entire webbing is visible during inspection.
The round sling (tubular) has a core of polyester yarns enclosed in a textile cover, conforms better to round shapes and is made to a different standard, EN 1492-2. The webbing sling with eyes has an eye at each end and is attached to the hook or ring by its eyes. Choose the flat endless sling when you want wide webbing with no eyes at the ends, for use in a straight lift, choke hitch or basket hitch.
Recommended uses
- Bundled pipes, sections and bars, slung in a choke hitch
- Machined parts and light subassemblies
- Small equipment moved with a hoist or an overhead crane
- Loading and unloading packages and building materials
How to choose the sling
- Capacity: choose a sling whose working load limit, for the lifting mode you use, is at least equal to the mass of the load; take the value from the load table, not just the nominal capacity.
- Lifting mode: straight lift (factor 1.0), choke hitch (0.8) or basket hitch (2.0, 1.4 or 1.0, depending on the angle); the same sling has a different working load limit in each mode.
- Leg angle: when lifting with two slings or in a basket hitch, check the angle β to the vertical; do not lift at an angle β above 60°.
- Effective working length: choose it according to the distance between the hook and the attachment point and according to the way the sling passes around the load; the circumference is twice the effective working length.
- Webbing width: it depends on the capacity (30, 60, 90 or 120 mm); check that it fits the hook and the load.
Correct use
- Use edge protection wherever the sling bears on sharp edges.
- Do not use a knotted or twisted sling.
- Do not place the stitched joint of the loop on the hook, on an edge of the load or at the choke point.
- Between lifts, with the sling unloaded, reposition the loop so that the contact points with the hook and with the load are not always the same. Do not rotate the loop under load.
- When using a choke hitch, do not force the loop: let it tighten freely, at its natural angle (about 120°); otherwise the table value for the choke hitch no longer applies.
- Do not drag the sling along the ground or pull it out from under the load.
- Avoid jerking and shock loading when slinging and lifting the load.
- Centre the load and distribute it evenly across the sling or between the legs.
- Use the sling at temperatures between −40 °C and +100 °C. Polyester is attacked by strong alkalis; do not use the sling where such substances are present.
- Store the sling in a dry place, away from sunlight and heat sources.
Inspection and discard
- Inspect the sling visually before every use.
- The sling must be examined by a competent person at least once every 12 months, or more often depending on working conditions and the regulations in force.
- Discard the sling if the webbing has cuts, broken yarns, damaged edges or excessive wear.
- Discard the sling if it has glazed, melted or stiff areas, or signs of heat, friction or weld spatter.
- Discard the sling if it shows signs of chemical attack, deformation or foreign particles embedded in the webbing.
- Discard the sling if it has broken or damaged stitching, especially at the stitched joint of the loop, or if it has knots.
- Discard the sling if the label is missing or no longer legible.
Marking and label
- Every sling has a stitched label; the label for polyester is blue.
- The capacity can also be identified by the colour of the webbing: 1 t violet, 2 t green, 3 t yellow, 4 t grey. The colour helps with recognition, but the label remains the reference.
- Flat endless slings are manufactured to EN 1492-1, the standard for flat slings made of synthetic fibres, with a safety factor of 7:1.
- Without a legible label, do not use the sling.
Ordering, delivery and returns
Slings with special lengths are made to order and are excluded from the right of return, in accordance with Article 12.2 of the Terms and Conditions. The delivery time is given when the order is confirmed. Images are for illustration only.
Frequently asked questions
What does “2 m / 4 m” mean for a flat endless sling?
The first number (2 m) is the effective working length: the distance between the two ends of the loop, with the sling laid flat on a level surface. The second (4 m) is the circumference, that is, the total length of the webbing. In the selector on the page, the same pair is written “2M/4M”.
Which standard does the flat endless sling comply with?
The flat endless sling is a flat sling made of woven webbing and is manufactured to EN 1492-1, with a safety factor of 7:1. EN 1492-2 applies to round slings (tubular), which have a core of polyester yarns in a cover.
What sling capacity should I choose?
Choose the capacity according to the mass of the load and the lifting mode, reading the working load limit from the table on the page. Compared with a straight lift (factor 1.0), the same sling can lift more in a basket hitch with parallel legs (factor 2.0) and less in a choke hitch (factor 0.8).
Where should the stitched joint of the loop sit?
The stitched joint must not be placed on the hook, on an edge of the load or at the choke point. Between lifts, with the sling unloaded, reposition the loop so that wear does not build up in the same place.
How often should a flat endless sling be inspected?
The sling must be inspected visually before every use. In addition, it must be examined by a competent person at least once every 12 months, or more often depending on working conditions and the regulations in force.
When should I discard the sling?
Discard the sling if the webbing has cuts, broken yarns, damaged edges or excessive wear; if it has glazed, melted or stiff areas, signs of heat, friction or chemical attack, deformation or embedded particles; if it has broken stitching or knots; or if the label is missing or can no longer be read.
Can slings with a special length be returned?
No. Slings with special lengths are made to order and are excluded from the right of return, in accordance with Article 12.2 of the Terms and Conditions.





Reviews
There are no reviews yet.